Видео

what battery do i need mine keeps shutting off with the small battery i got from my drill

Would it be better to use silicone instead of plumbers putty?

Тут еще дело зависит не так от инструмента,как от акб,насколько мне известно,что макита более ответственно относится к защите инструмента и акб и они настроены чуть мягче при нагрузке,вот и весь секрет!!!

I have used the Milwaukee exclusively over the last year. Job after job. I have lots of Milwaukee tools. The m12 battery design is always coming loose and falling out. Everyone on the jobs also have the same problem with m12 batteries. The dewalt won’t come loose. My camera locator is m12 and hasn’t come loose yet. It doesn’t get the same abuse. My Milwaukee 120ft camera uses m18 batteries.

Can the switch for the corded work on the cordless? I need a replacement switch for my dcw210 but not seeing one for it

Your vid helped with deciding and got myself the Klein. Thank you

Отличная демонстрация возможностей реноватора!👍🏻

nice to see someone finally compare the two platforms. To be clear the rapid seal heads don't open as much as the standards for the sake of only stretching what is necessary to make the connection which is essential in cold environments where the connection takes much longer to contract hence "Rapid Seal". Given the brushless fuel motor it makes sense to be a hair or two faster. The DCE410 is significantly bigger/heavier but can do 3/8" to 1-1/2" pex. Both solid tools but the non brushed m12 is a more accurate match up. Here I'd say the M12 fuel the better choice as a tool especially since the kit costs 30 dollars more than the brushed m12 and you get everything but a charger and batteries which is fine since the brushed kit only comes with two 1.5 ah batteries ~ Work Smart

Great information

If anyone wants to know my preference, it's the Milwaukee.

can you adjust the power on this? It's ripping through some vinyl trim and I need to lower the punch- is this possible?

How does it turn on??

Yes, glad someone else notices that Milwaukee blades SUCK!

Starlock on the FLEX is a beast ! Not everything Milwaukee is good. The best thing Milwaukee HAS is a humongous tool platform unlike any other tool manufacturer. However better tools do exist without a doubt.

i will continue to use steel Hacksaw its more fast again LOL

good info about the different blades you used .

are those dewalt batteries in makita and Milwaukee tools?

I have the trimmer 20/60v could I buy the attachment and just add it???

Are the wheels metal? Except for the tread or is it plastic.

I have some of the bigger rigid pvc cutter, they are about the same, but I'm team Sawzall all day.

Did you have the same blade on the saws? I found my Milwaukee did much better when I replaced the original blade.

Can someone give me the list of items and material he used. What’s the name of the paper he used and the stuff he placed in the corner

Raptor je nejlepší

It’s crooked bro !! I use those not a fan

I have never cut pipe like that. You score it and spin the pipe.

lol you show up with that tool to cut pvc pipe on our jobs.. just go pack your stuff up and roll out

In a clean environment these are decent but these cutters suck if u work in a muddy environment. Ive broken countless pairs working underground utilities.

Use cellcore. Not that great on schedule 40. It’s too hard Chop saw works best though

Use a cut off so the blades too aggressive turn it backwards try twisting your pipes on before you get too deep into the cut especially on a smaller pipe

you dont habe a sawzall?

Sawzalls faster. It’ll even look like a Charlotte cut if you hold your tongue right 😂

Dear God just use a band saw

Always wear a mask when sawing fiberglass.

Thanks for this review, very useful and informative.

Saw one for the first time last week and have to say I’m intrigued.

Cast iron tub. Does it bust up fairly easy? Does it take a full size sledge hammer?

Great review! I’ve been on the fence about whether to buy a cordless nailer or with a compressor for my small shop. I did a quick check and found it’s cheaper to actually buy the tool only from HD, and get the battery and charger from Amazon. For the same $400, you can get two Milwaukee batteries and the charger in that price. Or get an upgraded battery. I was worried that tool + battery was going to be pushing $550-600, looks like you can find a deal under $350 too if you do tool from HD and just the same replacement battery and charger. (No bag though, which I don’t use anyway.)

Very cool product, I was thinking perhaps one could be sold with a bevel-er as well. Got a 2 in 1 kinda thing.

Looks like it wont fit inbetween tight bays...otherwise hood idea

Can this be reliable for cutting copper

To clarify this booster would not start my truck under 11 volts even when it lit solid green, which sometimes took feeding it multiple batteries for up to 20 minutes. Still, I think it's an interesting solution for smaller engines.

Bummer. I’ll stick with my Noco.

So much milwaukee hate… you must have a different brand oewalf than the rest of the planet! Cone on man! No time stamp… very unconvincing video!

Honest question here. I’ve never used dewalt but looking to start buying. I was told you can’t use flex volt batteries in non flex volt tools. Is this true? I’ve been using ryobi for many years but I’m no longer happy with the product but I’m trying to figure out exactly what to go for.

They should delete this model. And just put spinning mops on S8.

Really great informational video thank you!!

I'll take the compact power stack all day every day on an impact driver. No need to lug a huge battery all day long. Run time is not hindered because you can have multiple batteries charged and ready to go.

The Dewalt connects quite fast and is only $100 where I am. Milwaukee is $200-$275 here. ($209 on sale at Home Depot) Personally I prefer the Dewalt attachment it fits in my bag and hooks up fine to any impact I've tried.

Looks quick

Thanks for spending the time to purchase and review these cutters! Underrated channel for sure!